Exchange 2003 限制信件傳遞的設定有以下幾個地方:
1) 通用設定\郵件傳遞
2) 預設 SMTP 虛擬伺服器\郵件
3) Send Connector
4) User Setting
官方回答:http://support.microsoft.com/kb/322679/zh-tw
以下是微軟網站中對於email進到exchange 2003後如何判斷大小限制的流程,個人感覺它晝得很清楚。http://technet.microsoft.com/zh-tw/library/dd159861.aspx
值得注意的是實作限制時,必須一併考量包含二進位附件且透過 SMTP 在路由群組之間流動而增加的額外郵件量。對於在路由群組之間傳送的傳出 SMTP 郵件,Exchange Server 將以 Transport Neutral Encapsulation
Format (TNEF) 來轉譯附件,這種格式是採用 Bbase64 或 Quoted Printable 而非二進位。這會導致郵件大小增加約 33% (即email會增大三分之一的大小)
。
使用者可以使用約等於三分之一的係數來增加全域郵件限制大小來彌補此負荷,即可解決這個問題。
不論是工作所解決的問題或是吃喝玩樂統統記起來。 久而久之這些經驗的累積放在這Birdman知識管理blog供所有人搜尋,自然而然成為自己或大家的知識,這就是知識管理最有價值之處~~~Reuse~~~
搜尋此網誌
2013年1月22日 星期二
2013年1月17日 星期四
如何規劃安裝windows server r2 Read Only Domain Control (RODC)
有一些關念要建立,以下網站很好:
http://blog.pmail.idv.tw/?p=2688 ---實作有圖
http://technet.microsoft.com/en-us/magazine/ff679947.aspx --- 完整介紹
安裝RODC須注意事項
http://blog.pmail.idv.tw/?p=2688 ---實作有圖
http://technet.microsoft.com/en-us/magazine/ff679947.aspx --- 完整介紹
安裝RODC須注意事項
- 確認樹系功能等級是Windows Server 2003。
- 執行ADPREP /ForestPrep,擴充Schema。
- 執行ADPREP /DomainPrep,建立安全群組。
- 執行ADPREP /RodcPrep,增加唯讀網域控制站所需的屬性。
- 在網域中需有一部Windows Server 2008 r2伺服器為可寫入DC。
- 用RODC很多時候是放在分公司
- default user password不會放在RODC,建議改policy,將分公司同仁的password放在RODC上。指定快取分公司的使用者密碼,如此就可以減少廣域網路上的流量。
- 可新增兩個角色DNS and global catalog server roles
2013年1月10日 星期四
Cisco 3560G x24備份設定檔
在Cisco路由器或交換器,作用的組態是在RAM中且預設的啟動組態的位置為NVRAM。啟動組態應被備份以免組態遺失。這些備份組態複本可利用TFTP伺服器備份出來
。
copy running-config tftp指令可被用來備份組態檔。
此程序的歩驟如下:
先要Run一個tftp server
利用sw Console進入sw
>en
>password xxxx
Switch#copy running-config tftp:
Address or name of remote host []? 在此輸入tftp的IP---192.168.X.XXX
Destination filename [switch-confg]?直接Enter即可Switch
#exit
從TFTP伺服器restore路由器組態。
。
copy running-config tftp指令可被用來備份組態檔。
此程序的歩驟如下:
先要Run一個tftp server
利用sw Console進入sw
>en
>password xxxx
Switch#copy running-config tftp:
Address or name of remote host []? 在此輸入tftp的IP---192.168.X.XXX
Destination filename [switch-confg]?直接Enter即可Switch
#exit
從TFTP伺服器restore路由器組態。
- copy tftp running-config.
- Select a host or network configuration file at the prompt.
- Enter the IP address of the TFTP server where the configuration file is located.
- Enter the name of the configuration file or accept the default name.
- Confirm the configuration filename and the server address that the system
supplies
2013年1月9日 星期三
HP printer message reset 刪除印表機面板訊息,如何將HP printer Maintenace Kit count reset
HP Maintenance Message Reset Methods
維護碼
LaserJet 4250 09425004
LaserJet 4300 11430002
Color LaserJet CP3505 06350507
很好的網站: http://www.printertechs.com/tech-support/
如何將HP printer Maintenace Kit count reset
我的 LJ 4250及LJ P4015用Method 1 或 Method 2可解決,其它可參考
http://www.fixyourownprinter.com/reference/guides/reset/hp
2021/01有用Method 2解一台lj4250
Resetting the maintenance count.
After installing a maintenance kit, you should reset the printer's "Maintenance Count".
There are two ways to do this, depending on your firmware revision.
Method 1
1. Turn the product off.
2. Turn the product on.
3. Press and hold down the OK button while the memory is counting. The memory starts counting at 000MB immediately after you turn the power on.
4. Continue to hold down the OK button until all three LEDs are illuminated.
5. Release the OK button.
6. Press the up arrow (Navigation) button until the message New Maintenance Kit appears on the control panel display. If New Maintenance Kit is not an option then you have an old firmware version (see below).
7. Press the OK button once. Your maintenance count is reset.
Method 2
Some of the older firmware versions did not have the "New Maintenance Kit" option mentioned in the above procedure. In this case you can either update the printer's firmware to ad this feature or manually reset the maintenance count in the service menu as described below.
Enter the Service Menu -- Press the MENU button, and scroll through the list of menus until you see "SERVICE". Press OK.
Before you can enter the Service Menu, you will see a blank line on the screen where you are supposed to enter an access code:
On a LaserJet P4014, the access code is 05401408
On a LaserJet P4015, the access code is 05401508
On a LaserJet P4515, the access code is 05451508
Enter the code and press OK.
You will now be allowed into the Service Menu. Scroll through the list of options until you see, "Maintenance Count." Press OK.
Change the current maintenance count to "0" by pressing the number "0", and then pressing OK.
To confirm this, you can print an Information page
http://www.printertechs.com/printer-troubleshooting/service-menu-pin-codes
Resetting the maintenance count.
After installing a maintenance kit, you should reset the printer's "Maintenance Count".
There are two ways to do this, depending on your firmware revision.
Method 1
1. Turn the product off.
2. Turn the product on.
3. Press and hold down the OK button while the memory is counting. The memory starts counting at 000MB immediately after you turn the power on.
4. Continue to hold down the OK button until all three LEDs are illuminated.
5. Release the OK button.
6. Press the up arrow (Navigation) button until the message New Maintenance Kit appears on the control panel display. If New Maintenance Kit is not an option then you have an old firmware version (see below).
7. Press the OK button once. Your maintenance count is reset.
Method 2
Some of the older firmware versions did not have the "New Maintenance Kit" option mentioned in the above procedure. In this case you can either update the printer's firmware to ad this feature or manually reset the maintenance count in the service menu as described below.
Enter the Service Menu -- Press the MENU button, and scroll through the list of menus until you see "SERVICE". Press OK.
Before you can enter the Service Menu, you will see a blank line on the screen where you are supposed to enter an access code:
On a LaserJet P4014, the access code is 05401408
On a LaserJet P4015, the access code is 05401508
On a LaserJet P4515, the access code is 05451508
Enter the code and press OK.
You will now be allowed into the Service Menu. Scroll through the list of options until you see, "Maintenance Count." Press OK.
Change the current maintenance count to "0" by pressing the number "0", and then pressing OK.
To confirm this, you can print an Information page
http://www.printertechs.com/printer-troubleshooting/service-menu-pin-codes
HP Printer Model | Service Menu PIN Code |
LaserJet 2300 | 11230002 |
LaserJet 2410 | 10241004 |
LaserJet 2420 | 10242004 |
LaserJet 2430 | 10243004 |
Color LaserJet 3000 | 11300005 |
Color LaserJet 3500 | 10350003 |
Color LaserJet 3550 | 10350003 |
Color LaserJet 3600 | 11360005 |
Color LaserJet 3700 | 10370003 |
Color LaserJet 3800 | 11380005 |
LaserJet 4100 MFP | 04410002 |
LaserJet 4101 MFP | 04410002 |
LaserJet 4200 | 11420002 |
LaserJet 4240 | 04424005 |
LaserJet 4250 | 09425004 |
LaserJet 4300 | 11430002 |
LaserJet 4345 MFP | 11434504 |
LaserJet 4350 | 09435004 |
Color LaserJet 4600 | 04460002 |
Color LaserJet 4610 | 05465004 |
Color LaserJet 4650 | 05465004 |
Color LaserJet 4700 | 09470005 |
Color LaserJet 4730 MFP | 09473005 |
LaserJet 5200 | 05520006 |
Color LaserJet 5500 | 04550002 |
Color LaserJet 5550 | 09555004 |
LaserJet 9000 | 00900001 |
LaserJet 9040 | 04904005 |
LaserJet 9050 | 09905004 |
LaserJet 9500 | 04950003 |
LaserJet 9000 MFP | 00900001 |
LaserJet 9040 MFP | 11904004 |
LaserJet 9050 MFP | 09905004 |
Color LaserJet 9500 MFP | 04950003 |
LaserJet CP4005 | 10400506 |
Color LaserJet CP3505 | 06350507 |
Color LaserJet CP4005 | 10400506 |
Color LaserJet CP6015 | 03601508 |
LaserJet M3027 | 11303506 |
LaserJet M3035 | 11303506 |
LaserJet M4345 | 11434506 |
LaserJet M4555 | 04455511 |
LaserJet M5025 | 11503506 |
LaserJet M5035 | 11503506 |
LaserJet P3005 | 10300506 |
LaserJet P3015 | 07301509 |
LaserJet P4014 | 05401408 |
LaserJet P4015 | 05401508 |
LaserJet P4515 | 05451508 |
HP Printer Model | Service Menu PIN Code |
LaserJet 2300 | 11230002 |
LaserJet 2410 | 10241004 |
LaserJet 2420 | 10242004 |
LaserJet 2430 | 10243004 |
Color LaserJet 3000 | 11300005 |
Color LaserJet 3500 | 10350003 |
Color LaserJet 3550 | 10350003 |
Color LaserJet 3600 | 11360005 |
Color LaserJet 3700 | 10370003 |
Color LaserJet 3800 | 11380005 |
LaserJet 4100 MFP | 04410002 |
LaserJet 4101 MFP | 04410002 |
LaserJet 4200 | 11420002 |
LaserJet 4240 | 04424005 |
LaserJet 4250 | 09425004 |
LaserJet 4300 | 11430002 |
LaserJet 4345 MFP | 11434504 |
LaserJet 4350 | 09435004 |
Color LaserJet 4600 | 04460002 |
Color LaserJet 4610 | 05465004 |
Color LaserJet 4650 | 05465004 |
Color LaserJet 4700 | 09470005 |
Color LaserJet 4730 MFP | 09473005 |
LaserJet 5200 | 05520006 |
Color LaserJet 5500 | 04550002 |
Color LaserJet 5550 | 09555004 |
LaserJet 9000 / 9000 mfp | 00900001 |
LaserJet 9040 | 04904005 |
LaserJet 9040 mfp | 11904004 |
LaserJet 9050 / 9050 mfp | 09905004 |
Color LaserJet 9500 / 9500 mfp | 04950003 |
Color LaserJet CP3505 | 06350507 |
Color LaserJet CP3525 | 09352508 |
Color LaserJet CP4005 | 10400506 |
Color LaserJet CP4025 | 11402509 |
Color LaserJet CP4525 | 11452509 |
Color LaserJet CP6015 | 03601508 |
LaserJet M601 | 10060311 |
LaserJet M602 | 10060311 |
LaserJet M603 | 10060311 |
LaserJet M3027 | 11303506 |
LaserJet M3035 | 11303506 |
LaserJet M4345 | 11434506 |
LaserJet M4555 | 04455511 |
LaserJet M5025 | 11503506 |
LaserJet M5035 | 11503506 |
LaserJet P3005 | 10300506 |
LaserJet P3015 | 07301509 |
LaserJet P4014 | 05401408 |
LaserJet P4015 | 05401508 |
LaserJet P4515 | 05451508 |
訂閱:
文章 (Atom)